Sunergy

Interesting collaboration between Kaitlyn Aurelia Smith and Suzanne Ciani.
Recording is coming out on September 16, 2016.

Karelian Skies 2016

I'm honoured to play this year's Karelian Skies concert together with great musicians. There are now seven of us and we are going to create together something special for the 16st of July concert in Nurmes-talo. More information here:

www-pages with fotos
facebook-event

First Flight

Kaitlyn Aurelia Smith is flying high !

Moog Prodigy alignment notes

Alignment steps are documented in Prodigy's Technical Service Manual. When doing the temperature adjustment of OSC1 and OSC2 I found David Morrins instructions very valuable. When adjusting the temperature trimmer I always checked that the voltage at pin 7 of U2/U4 was negative. If this voltage jumps to positive voltage then the heater circuit is saturated and will not track temperature. If this happens turn the R14/R35 trimmer to other direction so that you get the pin 7 back to negative region.

Original Prodigy's OSC1 is tuned lower (32-16-8) than OSC2 (16-8-4). This is not necessary if you are using the external keyboard-input that doesn't have the 2.5 octave limitation of Prodigy's keyboard. I tuned the OSC2 similarly to OSC1.

Moog Prodigy BOM

Here is an Excel-list for the Mouser-parts needed to build my Eurorack Moog Prodigy
Missing from this list are the 24mm potentiometers and the DP3T/DPDT switches.  Also Mouser can not source the CA3046/LM3046 and CA3080 chips. You can try BanzaiMusic for these.
Here is a picture of the 24mm 1M-log Alpha-pot I used for R155,R158,R166 and R169. Shaft length is 15mm and the diameter is 6.3mm. The other potis are similar size and look but from CTS (R83/3M-log, R106/3M-log and R136/50k REV-LOG). I sourced these potentiometers and switches from Uraltone and BanzaiMusic

Prodigy PCB 4.4E building details

Other end of resistors R59 and R41 must be connected directly to +12V.

C8 must be a high quality polystyrene or polyester film type.

C14 must be as the C8.

Here is one jumper that is needed.

Jumpers J1 and J2 are also installed. Here you can also see the optional headers at pin 5 of U2B and across R17. These headers make the temperature alignment procedure easier.

Here you can also see two jumpers and the ferrite cable cores in power-input.

Boards 1 and 2 are connected with direct cables. Note that these are not tight so that the alignment to front panel is easier.

TRIG IN must be connected to +12V so that KYBD IN 1V/Oct input is tracked all the time. C23 and R82 can be left out. They create a small CV-glide to KYBD IN. KYBD SCALE trimmer is installed but not used. I keeped the Keyboard current-source electronics (R92,R93,R91,R94,C22,RKYBD) here but it can be leaved out. The other half of U11 must then be bypassed correctly.

Here you can see the alignment headers for OSC2 temp adjustment.

RKYBD can be 200R resistor. This replaces the keyboard resistor divider.

Here is the input connector for 20k resistor and the output of U13A to make the VCA adjustment easier.

The TE Headers are soldered to the bottom side (Wheels and PWM-inputs).

I used only the potentiometers from Doepfers Wheels module.

EWI and Moog

My Akai EWI windcontroller works great with Moog Prodigy. Here the filter is closed and drone-mode is used. EWI controls the pitch and filter cutoff. I created this with looper, reverb and delay pedals. It's amazing how much control of the sound you get with just these two control CV's.